• Cambrionix
  • ABI Electronics
  • Saelig-Kerr
  • Disklabs
  • ThinkRF
  • Rigol MSO
  • SAF Tehnika
  • Saelig Values
  • HT Instruments
  • JRE Test
  • Preen
  • PS4000A
  • Saelig 34 Years in business!
  • Teledyne LeCroy Wavesurfer 3000z Promo
  • Siglent SSA3000X-R
  • Tekbox
  • Windfreak
  • Rigol MSO5152-E
  • Teledyne LeCroy Free Products
  • GL Optic
  • Siglent SDS1000X-E
  • PicoScope 6000E
  • Micsig
  • Rigol RSA5000
  • Rigol Promotions
  • SDM3000
  • Not Your Average Web Store
  • Saelig Newsletter Signup
  • LD400
  • Saelig Name Origins
  • Sensepeek
  • Your Technical Distributor
  • ChargeBox
  • Teledyne LeCroy Wavesurfer 4000HD Promo
  • YouTube Videos
  • MegiQ
  • Saelig Scope Selection
  • Choosing An Oscilloscope
  • Free Shipping

SynthUSBII USB RF Signal Generator

    SynthUSBII USB RF Signal Generator

    Manufacturer: Windfreak Technologies

    Price: $239.00


    Saelig GSA Schedule Logo

    • Description
    • Downloads

    The Windfreak SynthUSBII is a 34.4MHz to 4.4GHz software tunable RF signal generator controlled and powered by a PC running Windows XP, Vista, Windows 7 or 8 via its USB port.

    The SynthUSBII also has nonvolatile on board memory so it can be programmed to fire up by itself on any frequency, power, sweep or modulation setting. This makes for a highly mobile, low power and light weight solution for your RF signal generation needs.

    Use this device as a generic RF signal generator in your test setup, or use it as a high quality local oscillator in your RF / microwave communication system.

    Shown below, the software is eloquently engineered giving professional performance at fractions the cost of a bench top generator.

    You may enter data either with the touch pad, knob, directly with the PC keyboard, and also by clicking on arrows next to the controls.

    RF single frequency generation tab.

    SWGEN Image

     RF sweep generation tab. (Step as fast a 300uS per point. Resolution as low as 1KHz per step.)
    SWSweep Image
    RF Pulse Amplitude Modulation tab. (Minimum pulse size and resolution is 1mS. Please see SynthNV for higher performance.)
    SWMod Image
    PLL Control tab. (Control some finer details of the ADF4351 chip to get higher accuracy or quality for a particular frequency.)
    SWReg Image
    Extras tab. (Check SynthUSBII firmware version, save to SynthUSBII internal EEPROM memory Frequency, Power, Modulation and Sweep setup for standalone operation. Also poll every second for phase lock.)
    SWExtra Image
    RF power is controlled by two bits in the PLL chip. There is a total of 10dB of output power adjustment in 4 total steps. Please check out the SynthNV for more power and 1/2dB steps.
    The software is easy to install and use. It can control multiple devices based on programmed serial numbers, tune a RF CW frequency, run a RF sweep, Pulse Modulate, save many settings to EEPROM, and fine tune the PLL registers for experienced users. Control is very similar to a bench top signal generator. It is also touch panel friendly.
    This software was written in Labview and the open source code is included so that you can modify and enhance any way you see fit for your own use. Please do not distribute. If you don't own Labview, you will also get an executable that will install standalone and run on a PC. If you want to write your own software, it is best to get Labview and reverse engineer the Windfreak Labview source code. Labview is available with a free 1 month trial from National Instruments. All source code is sent on CD "saved as" using the latest version of Labview Basic. The device is easy to talk to via 1 simple command character followed program data. For example, setting frequency is done by sending "f1000.0" (without the quotes).
    Click here to see the format for serial communications via the proprietary Windfreak firmware:
    The hardware:
    synthusbiipcb Image
    The SynthUSBII is made in the United States from parts purchased in the USA via manufacturers certified vendors.
    The technology is based on Analog Devices ADF4351 chip seen here:  click here for the ADF4351 Datasheet
    You can expect high quality RF performance at the RF connector similar to the specs in the datasheet.
    RF power (max) into a 50 ohm load is similar to this:
    FREQ RESP Image

    RF generator accuracy is based on an onboard 2.5ppm 10MHz crystal oscillator. All parts on the PCB are specified to operate from -40 to +85C.

    The synthesizer will run off USB power. It will also run standalone without a PC connected if you have a USB power supply similar to an iphone charger. The required voltage is 5 volts DC at <200mA.

    Hub 7 Image

    You can run them all with one GUI, or run one GUI for each device for quick individual adjustments. The spectrum plot to the right was taken with a crude cut wire antenna. Hence the unequal powers in each carrier.

    SWMulti Image

    The Atmel microcontroller on board is an ATmega32U2 and comes programmed with Windfreak Technologies proprietary firmware to allow basic control of the whole device. In conjunction with that, it also has the Atmel boot loader so that custom firmware can be loaded through USB by the end user.

    USB communication is done via a virtual comm port directly to the microcontroller. Drivers are included with the software. The SynthUSBII can plug straight in to your PC. A USB type A extension cable is recommended but not included.

    Included with all of this are softcopies of the PC board schematics and a PCB reference designator map on the CD. This way you can see what bus wires are used to control the synthesizer chip and PA.

    Note: Please look under the pink foam in the shipping box for the CD and instructions.

    On board the PCB are 2 troubleshooting LEDs: LED1 shows USB power upon startup, and LED2 shows phase lock on the programmed frequency. LED1 also blinks during USB communication. Both LEDs blink when a USB command is not understood. This helps with custom software development.

    Compare this unit to other solutions worth thousands of dollars. We've invested hundreds of man hours on software that you get to build upon for highly custom applications.

    Some applications include: wireless communications systems, microwave point to point backhaul radios, Software Defined Radio (SDR), radar, Automated Test Equipment (ATE), sweeping and hopping, electronic warfare (EW), Phase Lock Loop (PLL) Synthesizer Design, Local Oscillator (LO) replacement, and hobbyist radio development.

    Customers who purchased this product, also purchased...

    Free UPS Ground Shipping On Orders Over $99

    Sign up for our newsletter containing updates and exclusive content!

    Customer Reviews

    Privacy Policy|Terms and Conditions|RoHs|Quality Statement|Returns|Sitemap

    © 2007- Saelig Company, Inc. All Rights Reserved.
    Other products, logos and company names mentioned herein, may be trademarks of their respective owners.
    eCommerce Shopping Cart Software by Miva Merchant